联系我们收藏本站在线留言网站地图欢迎进入唐山天物彩板有限公司官网!

彩板厂家_彩涂板价格_彩涂卷厂家_彩涂板价格_唐山彩涂板厂家

天物彩板-始于2004 专注功能性高端彩板生产销售
服务热线: 400-060-9166
服务热线: 13931586578
彩板厂家

彩涂板的加工过程中怎么做好精度的把控

返回列表 来源: 发布日期: 2019.10.28

彩涂板的加工过程中怎么做好精度的把控

天物彩板一站式服务——更多天津彩涂板加工厂家_安徽蚌埠彩板厂家_天物彩板请拨打网站上方电话咨询

天津彩涂板钣金加工厂家_安徽蚌埠彩板厂家_天物彩板

彩涂板行业的人士都知道,整个彩涂板工程的铝单板并不是直接按照图纸一次性全部生产出来的,而是直接交给施工方。它是一批货物完成生产后,让施工人员完成安装,然后再进行下一批生产加工。这就要求彩涂板生产厂家的产品误差不能太大。一开始的小误差会使后期的彩涂板加工面临数据问题,而产品很容易遇到安装问题,这就是所谓的“损失一点,谬误千里”。
在这方面,整个彩涂板加工行业实际上都有相关的国家推荐标准,其中对相应的参数规定得非常细致和严格。一般来说,彩涂板的尺寸和规格由厚度、长度、宽度、卷边高度、对角线差等组成,长度和宽度决定了整个彩涂板的基本形状,而厚度则会影响整个彩涂板的性能。无论彩涂板的形状如何,其厚度误差在±0.1mm以内。当镀铬板的长度和宽度小于或等于2000 mm时,长度和宽度的最大允许误差为1 mm。当长宽大于2000mm时,长宽误差不应超过1.5mm。
卷边高度的误差范围与彩板尺寸无关,不能超过0.5mm。彩涂板长度小于等于2000mm时对角线差允许误差范围为2mm,大于2000mm时对角线差允许误差范围为3mm。
彩涂板的钣金加工是由机器上的技术工人在生产线上进行的。由于各种原因,加工后的彩涂板可能存在一定的误差,但这种误差必须控制在一定范围内,否则就是不合格产品。这些错误必须尽量减少,最好完全避免!无论是钣金加工还是喷涂加工,都必须注意精度。

People in the color coated board industry know that the aluminum veneer of the whole color coated board project is not produced completely at one time directly according to the drawings, and is directly handed over to the construction party. It is a batch of goods after the completion of production, let the construction workers complete the installation, and then the next batch of production and processing. This requires that the product error of the color coated plate manufacturer should not be too large. A small error at the beginning will make the later color coated plate processing face the problem of data, and the product is easy to encounter the problem of installation, which is the so-called "loss of a little, fallacy of a thousand miles".

In this respect, the whole color coated plate processing industry actually has relevant national recommended standards, in which the corresponding parameters are specified very carefully and strictly. Generally, the size and specification of color coated plate are composed of thickness, length, width, hem height, diagonal difference, etc. Length and width determine the basic shape of the whole color coated plate, while thickness can affect the performance of the whole color coated plate. No matter what the shape of the color coated plate is, the thickness error range is within ± 0.1mm. When the length and width of the color coated plate is less than or equal to 2000 mm, the maximum allowable error of length and width is 1 mm. When the length and width are more than 2000mm, the error of length and width shall not exceed 1.5mm.
The error range of hem height has nothing to do with the size of color coated plate, and it can never exceed 0.5mm. The allowable error range of diagonal difference is 2mm when the length of color coated plate is less than or equal to 2000mm, and 3mm when the length is greater than 2000mm.
The sheet metal processing of color coated plate is carried out on the production line by technical workers on the machine. Due to various reasons, there may be certain errors in the processed color coated plate, but this error must be controlled within a certain range, otherwise it is unqualified product. These errors must be reduced as much as possible, and it is better if they are completely avoided! Attention must be paid to the accuracy whether it is sheet metal processing or spraying process.
【相关推荐】

咨询热线

400-060-9166