联系我们收藏本站在线留言网站地图欢迎进入唐山天物彩板集团有限公司官网!

彩板厂家_彩涂板价格_彩涂卷厂家_彩涂板价格_天物集团

天物彩板-始于2004 专注功能性高端彩板生产销售
服务热线: 400-060-9166
服务热线: 13931586578
彩板厂家

关于彩钢板开孔的相关介绍

返回列表 来源: 发布日期: 2019.10.08

关于彩钢板开孔的相关介绍

天物彩板专注定制高端彩板16年——关于更多洁净室彩钢板定制_彩钢板顶板打孔资讯请拨打网站上方电话咨询洁净室彩钢板定制_彩钢板顶板打孔_天物彩板

作为所有洁净室服务设施(风、水、电、工艺管道)的承载力,将有许多相应的孔洞需要开挖。这些洞主要分为以下几类。
大型方孔:大型方孔多出现在屋顶上。在屋顶安装期间,可根据相应图纸钻孔。在冲孔过程中,应检查图纸,以防止低级错误。规定孔的四面与彩钢板边缘平行。手锯或曲线锯可用于钻孔。任务完成后,可用铝槽做手侧孔。
大型圆孔:一般见于通风系统中,此类孔需由相关专业人员油漆,用曲线锯打井,锯片长度宜选择10cm左右,而封边可用圆形装饰片或干净的套管完成任务。
小面积圆孔:小面积圆孔多见于管道专业。要完成此任务,应使用相应的大小开瓶器。如果穿孔管必须绝缘,则应在屋顶上下两侧的绝缘接头处使用密封胶。如果船用板管不需要保温,应做好干净套管边缘与射孔管的密封。
小方孔:小方孔通常出现在垂直墙板上,电气和设备开口很常见。因此,规定了孔的位置,并在标记后用手摇磨床钻孔。
在时间允许的情况下,彩钢板屋面穿孔由厂家完成。我们需要详细检查现场和图纸,确保每个孔的穿孔位置与现场一致。

As the bearing capacity of all clean room service facilities (wind, water, electricity and process pipelines), there will be many corresponding holes that must be excavated. The holes are mainly divided into the following categories.


Large-scale square holes: large-scale square holes mostly appear on the roof. During the installation period of the roof, holes can be drilled according to the corresponding drawings. In the process of punching, drawings should be checked to prevent low-level errors. It is stipulated that all sides of the holes are parallel to the edges of the colored steel plate. Hand saw or curve saw can be used to drill holes well. Aluminum groove can be used to do the hand side of the holes after the task is completed.

Large-scale circular holes: usually seen in ventilation systems, such holes need to be painted by relevant professionals, drilled well with curve saw, the length of saw blade should be selected about 10 cm, while the edge can be closed with circular decorative patches or clean casing to complete the task.

Small area circular holes: Small area circular holes are usually found in pipeline specialty. To complete the task, the corresponding size openers should be used. If the perforating pipe must be insulated, the sealing glue should be used at the insulation joints of the upper and lower sides of the roof. If the ship plate pipe does not need to be insulated, the sealing of the edge of the clean casing and the perforating pipe should be done well.

Small square holes: Small square holes usually appear on vertical wall panels, and electrical and equipment openings are common. Therefore, the location of the holes is specified, and the holes are made by hand grinder after marking.

When the time limit permits, the perforation of color steel plate roof should be completed by the manufacturer. We need to check the site and drawings in detail to ensure that the perforation position of each hole is in line with the site.
【相关推荐】

咨询热线

400-060-9166